Merlin Powerlift Installationsanleitung

© 2005 Directed Electronics, Vista, CA N225T 10-05installation guide3000®

© 2005 directed electronics—all rights reserved8valet switch1. The Valet/program switch needs to be placed in a position where the customerhas easy ac

© 2005 directed electronics—all rights reserved9primary harness wire connection guideprimary harness wiring diagram___[______________________[_______[

© 2005 directed electronics—all rights reserved10The BLACK wires in the harness are identified with labels describing their function (seetable below).

© 2005 directed electronics—all rights reserved11h3 red/white auxiliary channel outputThis wire produces a 200mA output when activated by the remote c

© 2005 directed electronics—all rights reserved12h10 red low current 12V—LEDThis wire connects to the LED through the BLACK mini-connector, pin 1.h10

© 2005 directed electronics—all rights reserved13h17 yellow ignition input (+)12 VConnect this wire to any ignition wire on the motorcycle that remain

© 2005 directed electronics—all rights reserved14remote start shunt input when ground is applied during remote start and aux outputis programmed to re

© 2005 directed electronics—all rights reserved152. For the key blade to fit properly it will need to be approximately 9/32–incheswide for the plastic

© 2005 directed electronics—all rights reserved16arming/disarming diagnosticsThe systems microprocessor monitors and reports all active and violated z

© 2005 directed electronics—all rights reserved17high security disarmWhile the siren is sounding, press the arm/disarm button once to silence the sire

Bitwriter®, Code Hopping®, Directed®, Doubleguard®, ESP®, FailSafe®, Learn Routine™, Merlin®, Nite-Lite®,Nuisance Prevention®, NPC®, Revenger®, Silent

© 2005 directed electronics—all rights reserved18valet modePrevents the security system from automatically arming. In Valet Mode, the securitysystem w

© 2005 directed electronics—all rights reserved19system features programmingThis system has many features that can be programmed to accommodate the us

© 2005 directed electronics—all rights reserved20If the feature has more than two settings, continue pressing the arm/disarm but-ton on the transmitte

© 2005 directed electronics—all rights reserved21user selectable featuresuser selectable features descriptions - column oneadd new remote (for 3-butto

© 2005 directed electronics—all rights reserved22chirps - off/loud/quietzOff: Chirps will not sound when arming/disarming the system (with the excep-t

© 2005 directed electronics—all rights reserved23npc on/offNuisance Prevention®Circuitry (NPC®) stops repeated triggering of the same zone. Ifone zone

© 2005 directed electronics—all rights reserved24silent modezThe transmitter channel programmed into this feature will arm/disarm thesystem, but the s

© 2005 directed electronics—all rights reserved25installer selectable features descriptions - column oneaccessory output auto activation - off/arm/dis

© 2005 directed electronics—all rights reserved26zLatched (ignition reset): The output is controlled by pressing the button(s) control-ling the access

© 2005 directed electronics—all rights reserved27horn honk - pulsed/latchedzPulsed: H5 YELLOW/WHITE wire will generate a pulsing (-) output when theal

contentswhat is included . . . . . . . . . . . . . .3transmitter configurations . . . . . .3transmitter functions . . . . . . . . . .4standard confi

© 2005 directed electronics—all rights reserved28zProgramming Procedure1. Enter the feature location (column 2, row 1) in the user-selectableprogrammi

© 2005 directed electronics—all rights reserved29rapid resume logicThe Rapid Resume Logic feature ensures that when the security system is poweredback

© 2005 directed electronics—all rights reserved30Disarm the system when immobilizedUse one of the following methods to turn off auto-immobilizationzTu

© 2005 directed electronics—all rights reserved31zOpen or close the switch or circuit connected to the normally open/normallyclosed programmable input

© 2005 directed electronics—all rights reserved32

© 2005 directed electronics—all rights reserved33wiring quick reference guideLEDStarterMotorIgnition Coil orFuel Pump relayLeftIndicatorLightRightInd

© 2005 directed electronics—all rights reserved34

© 2005 directed electronics—all rights reserved35notes________________________________________________________________________________________________

© 2005 directed electronics—all rights reserved2

© 2005 directed electronics—all rights reserved3what is includedzOne control module/siren, withzOne 3-button transmitterbuilt-in Tilt sensor and 24-pi

© 2005 directed electronics—all rights reserved4transmitter functionsThis system uses computer-based code learning to learn the transmitter buttons. T

© 2005 directed electronics—all rights reserved5installationcontrol moduleIIMMPPOORRTTAANNTT::The control unit mmuusstt be installed as far away as p

© 2005 directed electronics—all rights reserved6protection switchThe long lever switch should be installed in a position that requires a part of the m

© 2005 directed electronics—all rights reserved7LED status indicator1. Select a prominent location on the motorcycle that is highly visible from all d